JustFlight PA-28-161 Warrior II v0.1.0

[zebulon]

Hi,


https://file.cm/hwi7o6ukbnd9

[zebulon]

Hi,

V0.1.1
https://file.cm/853ntlgaf1bm

[zebulon]

Hi,

v0.2.0
- PMS-50 GTN 650 integration
- FDE Tweaks
- Wheel fairing option saved with state
- Dome light texture position fixed
- Beacon light control assignments fixed
- Turn coordinator texture fixed
- EFB sounds on/off clickspots*added
- EFB warning added for engine flooding due to incorrect primer usage. Flooding prior to flight can now be resolved either by following the POH checklist (engine start with mixture/fuel pump off) or by waiting for a short period. Flooding in flight will now cause temporary engine splutter rather than total failure.
- Cockpit texture tweaks for improved appearance
- Tutorial flight plan fixed
- KN62 inner knob animation fixed
- Sim Update V control system compatibility fixes:
* Cabin heating controls
* Parking brake lever
* Window latch
* HSI and DI knobs
* GPS 100 ON/OFF button
https://file.cm/1pt84xiqtbbc

[zebulon]

Hi,

v0.3.1
Note: SEE README.TXT AFTER EXTRACTING! Please follow the activation procedure again even if you used previous version of this aircraft.

Changelog :
v0.3.1:

Elevator trim axis has limited range - fixed
COM/NAV radio volume and power logic improvements
Further tweaks to cockpit instrument reflections
Cockpit screen clickspot logic improvements
Landing light effect repositioned for better match with model
PUMP ON and PUMP OFF assignments fixed
Pilot visible when cold & dark – fixed

v0.3.0:

Exterior model parts (e.g. pilot) showing up in cockpit when a flight is ended - fixed
EFB tab black edges - fixed
Version number is now shown on the top bar of the EFB
OAT is now shown on the top bar of the EFB (Fahrenheit or Celsius depending on selected MSFS unit of measure)
Wheel touchdown effects added
Cabin heat control interactions fixed
Beacon light no longer remains off when in cockpit view
PUMP ON and PUMP OFF assignments can now be used to control the fuel pump switch
Elevator trim axis direction reversed to match behaviour of default aircraft
Panel lighting will now be set according to weather conditions as well as time of day as part of the aircraft states
KN62 DME speed/time not shown after flight has been restarted - fixed
Autopilot roll instability - fixed
Radio lights can now be manually adjusted with SET NAV LIGHTS assigned
Elevator trim wheel tooltip and mouse-wheel sensitivity - fixed
Dome light knob tooltip - fixed
Dome light will now fail if the overhead lights CB is pulled
COM/NAV volume now included in state save
Propeller texture/material tweaks
Transponder ident added
Exhaust heat haze direction fixed
Yoke timer usability in VR fixed
Sun visor reflections fixed
GPS 100 headwind/tailwind logic fixed
Rotating beacon is now controlled by the anti-collision lights switch
Exterior lighting effects improved
Instrument reflections reduced
Correct ASI and RPM scales added to HUD
Missing co-pilot fixed
https://file.cm/y071twoe0y9o

[zebulon]

Hi,

v0.3.2
Note: SEE README.TXT AFTER EXTRACTING! Please follow the activation procedure again even if you used previous version of this aircraft.
- Avionics switch no longer turns off when the battery master is selected off
- HUD flap scale fixed
- Rudder trim animation improved
- Elevator trim animation improved
- NAV 1 ident not audible - fixed
- DATCON and HOBBs animations fixed
- GPS 100 heading value no longer affected by drift
- Autopilot now supports on/off control assignments
- Pilot no longer visible in hanger view
- Minor sound tweaks
- ASI TAS scale position now included in state saving
- Altimeter inHG baro scale fixed
- TDS GTNXi integration added
- Updated manual
https://krakenfiles.com/view/YKjFnLHppC/file.html