11-20-2021, 05:54 PM
Hi,
v0.5.1
Changelog :
v0.5.1:
Elevator trim axis has limited range - fixed
PMS GTN 650/750 not powering up (bundle only) - fixed
COM/NAV radio volume and power logic improvements
Further tweaks to cockpit instrument reflections
Cockpit screen clickspot logic improvements
Landing light effect repositioned for better match with model
Pilot visible when cold & dark - fixed
v0.5.0:
Exterior model parts (e.g. pilot) showing up in cockpit when a flight is ended - fixed
EFB tab black edges - fixed
Version number is now shown on the top bar of the EFB
OAT is now shown on the top bar of the EFB (Fahrenheit or Celsius depending on selected MSFS unit of measure)
Wheel touchdown effects added
Arrow III, Turbo Arrow III and IV variants now have unique rather than shared state saving
The alternate air lever can now be controlled using the SET ANTI ICE and TOGGLE ANTI ICE assignments
Cabin heat control interactions fixed
Beacon light no longer remains off when in cockpit view
PUMP ON and PUMP OFF assignments can now be used to control the fuel pump switch
Elevator trim axis direction reversed to match behaviour of default aircraft
Panel lighting will now be set according to weather conditions as well as time of day as part of the aircraft states
KN62 DME speed/time not shown after flight has been restarted - fixed
Autopilot roll instability - fixed
Autopilot roll knob can now be controlled using the AILERON TRIM LEFT/RIGHT assignment
Radio lights can now be manually adjusted with SET NAV LIGHTS assigned
Elevator trim wheel tooltip and mouse-wheel sensitivity - fixed
Dome light knob tooltip - fixed
Dome light will now fail if the overhead lights CB is pulled
COM/NAV volume now included in state save
Propeller texture/material tweaks
Transponder ident added
Exhaust heat haze direction fixed
Yoke timer usability in VR fixed
Sun visor reflections fixed
GPS 100 headwind/tailwind logic fixed
Exterior lighting effects improved
Turbo Arrow III rudder trim indicator fixed
Oxygen cylinder valve ‘PRESSURE DUMP SWITCH’ control assignment fixed
Instrument reflections reduced
Correct ASI and RPM scales added to HUD
Missing co-pilot fixed
Mixture lever can be moved to idle cut-off with the lock engaged but the engine doesn’t cut - fixed
https://file.cm/53o0eh7diq6l
v0.5.1
Changelog :
v0.5.1:
Elevator trim axis has limited range - fixed
PMS GTN 650/750 not powering up (bundle only) - fixed
COM/NAV radio volume and power logic improvements
Further tweaks to cockpit instrument reflections
Cockpit screen clickspot logic improvements
Landing light effect repositioned for better match with model
Pilot visible when cold & dark - fixed
v0.5.0:
Exterior model parts (e.g. pilot) showing up in cockpit when a flight is ended - fixed
EFB tab black edges - fixed
Version number is now shown on the top bar of the EFB
OAT is now shown on the top bar of the EFB (Fahrenheit or Celsius depending on selected MSFS unit of measure)
Wheel touchdown effects added
Arrow III, Turbo Arrow III and IV variants now have unique rather than shared state saving
The alternate air lever can now be controlled using the SET ANTI ICE and TOGGLE ANTI ICE assignments
Cabin heat control interactions fixed
Beacon light no longer remains off when in cockpit view
PUMP ON and PUMP OFF assignments can now be used to control the fuel pump switch
Elevator trim axis direction reversed to match behaviour of default aircraft
Panel lighting will now be set according to weather conditions as well as time of day as part of the aircraft states
KN62 DME speed/time not shown after flight has been restarted - fixed
Autopilot roll instability - fixed
Autopilot roll knob can now be controlled using the AILERON TRIM LEFT/RIGHT assignment
Radio lights can now be manually adjusted with SET NAV LIGHTS assigned
Elevator trim wheel tooltip and mouse-wheel sensitivity - fixed
Dome light knob tooltip - fixed
Dome light will now fail if the overhead lights CB is pulled
COM/NAV volume now included in state save
Propeller texture/material tweaks
Transponder ident added
Exhaust heat haze direction fixed
Yoke timer usability in VR fixed
Sun visor reflections fixed
GPS 100 headwind/tailwind logic fixed
Exterior lighting effects improved
Turbo Arrow III rudder trim indicator fixed
Oxygen cylinder valve ‘PRESSURE DUMP SWITCH’ control assignment fixed
Instrument reflections reduced
Correct ASI and RPM scales added to HUD
Missing co-pilot fixed
Mixture lever can be moved to idle cut-off with the lock engaged but the engine doesn’t cut - fixed
https://file.cm/53o0eh7diq6l