Just Flight PA-28R Turbo Arrow III/IV v0.1.0

[zebulon]

Hi,



See README.txt after extracting

https://file.cm/wh3hmj6lc7s7

[zebulon]

Hi,

v0.1.1
See README.txt after extracting.
v0.1.1 Changelog:
- Cockpit texture resolution no longer reduced by the sim
- Custom registration decals fixed
- Turbocharger logic improvements
- Chocks and tie-downs now prevent movement of aircraft on ground
- PMS-50 GNS/GTN integration fixes (bundle version)
- 'Set Electric Fuel Pump 1' control assignment is now supported for Honeycomb hardware users

https://file.cm/m2816ldg0yxz

[zebulon]

Hi,

v0.2.0
- Portable oxygen system added (consumption rate varies depending on altitude and number of passengers, can be refilled on the ground)
- Improved cockpit lighting
- EFB brightness controls and battery power logic added
- VR compatibility tweaked for easier use of GTN 750
- Audio ident/selector fixes
- Autopilot altitude hold logic tweaks
- KX170/KX175 COM and NAV frequencies can now be controlled using the 'Increase/Decrease COM/NAV (WHOLE/FRACT)' assignments
- Turbocharger/manifold pressure logic improvements
- Aileron inputs disabled whilst autopilot is engaged to prevent control issues
- High oil pressure fixed
- Custom registration decals resized/repositioned
- VR zoom issue on Turbo Arrow III fixed
- Lower tail navigation light glass fixed
- Manifold pressure gauge night lighting fixed
- Turbo Arrow IV paint kit PSD fixed
- FDE improvements and fixes
- RPM drop with prop lever movement fixed
- Autopilot nav source select can now be assigned to a control
- Dome light non-illuminated texture fixed, state of knob now saved
- Missing German flag added to tail of D-EAIV
- D-ERMT registration alignment fixed
- Fuel state is now saved
- Turbo Arrow IV prop spinner now more reflective/shiny

https://file.cm/7b273wi4mj5t

[zebulon]

Hi,

v0.2.1
https://file.cm/86blbjbqy8bk

[zebulon]

Hi,

v0.3.0
- Autopilot logic fixes (including bank hold, altitude hold accuracy)
- Landing gear lights now dim when the panel lighting is switched on
- AP nav 1/2 selector fixed
- Radio frequency control assignments fixed
- Turbo Arrow IV cockpit texture resolution no longer degraded based on MSFS texture setting
- Whiskey compass accuracy improved
- External equipment now visible in VR
- Minor sound fixes and EFB sounds added
- KN62 inner knob push/pull for 0.5 KHz selection added
- KMA20 COM 1 receive logic fixed
- Cabin heat now prevents windshield icing
https://file.cm/lvoqo70z1p60

[zebulon]

Hi,

v0.4.0
- PMS-50 GTN 650 integration
- FDE Tweaks
- Autopilot control assignments fixed
- Landing gear lights dim more with panel lighting switched on
- EFB sounds on/off clickspots added
- Cockpit texture tweaks for improved appearance
- KN62 inner knob animation fixed
- Sim Update V control system compatibility fixes:
* Cabin heating controls
* Parking brake lever
* Window latch
* HSI and DI knobs
* GPS 100 ON/OFF button
https://file.cm/we3gxcmkj2ix

[zebulon]

Hi,

v0.5.1
Changelog :
v0.5.1:

Elevator trim axis has limited range - fixed
PMS GTN 650/750 not powering up (bundle only) - fixed
COM/NAV radio volume and power logic improvements
Further tweaks to cockpit instrument reflections
Cockpit screen clickspot logic improvements
Landing light effect repositioned for better match with model
Pilot visible when cold & dark - fixed

v0.5.0:

Exterior model parts (e.g. pilot) showing up in cockpit when a flight is ended - fixed
EFB tab black edges - fixed
Version number is now shown on the top bar of the EFB
OAT is now shown on the top bar of the EFB (Fahrenheit or Celsius depending on selected MSFS unit of measure)
Wheel touchdown effects added
Arrow III, Turbo Arrow III and IV variants now have unique rather than shared state saving
The alternate air lever can now be controlled using the SET ANTI ICE and TOGGLE ANTI ICE assignments
Cabin heat control interactions fixed
Beacon light no longer remains off when in cockpit view
PUMP ON and PUMP OFF assignments can now be used to control the fuel pump switch
Elevator trim axis direction reversed to match behaviour of default aircraft
Panel lighting will now be set according to weather conditions as well as time of day as part of the aircraft states
KN62 DME speed/time not shown after flight has been restarted - fixed
Autopilot roll instability - fixed
Autopilot roll knob can now be controlled using the AILERON TRIM LEFT/RIGHT assignment
Radio lights can now be manually adjusted with SET NAV LIGHTS assigned
Elevator trim wheel tooltip and mouse-wheel sensitivity - fixed
Dome light knob tooltip - fixed
Dome light will now fail if the overhead lights CB is pulled
COM/NAV volume now included in state save
Propeller texture/material tweaks
Transponder ident added
Exhaust heat haze direction fixed
Yoke timer usability in VR fixed
Sun visor reflections fixed
GPS 100 headwind/tailwind logic fixed
Exterior lighting effects improved
Turbo Arrow III rudder trim indicator fixed
Oxygen cylinder valve ‘PRESSURE DUMP SWITCH’ control assignment fixed
Instrument reflections reduced
Correct ASI and RPM scales added to HUD
Missing co-pilot fixed
Mixture lever can be moved to idle cut-off with the lock engaged but the engine doesn’t cut - fixed
https://file.cm/53o0eh7diq6l

[zebulon]

Hi,

v0.5.2
Note: SEE README.TXT AFTER EXTRACTING! Please follow the activation procedure again even if you used previous version of this aircraft.
- Autopilot roll control logic rewritten for greater reliability and accuracy
- HUD flap scale fixed
- Rudder trim animation improved
- Elevator trim animation improved
- NAV 1 ident not audible - fixed
- DATCON and HOBBs animations fixed
- GPS 100 heading value no longer affected by drift
- Autopilot LOC mode fixed
- Autopilot now supports on/off control assignments
- FDE improvements
- Pilot no longer visible in hanger view
- Minor sound tweaks
- ASI TAS scale position now included in state saving
- TDS GTNXi integration added
- Updated manual
https://krakenfiles.com/view/eJelysjuh2/file.html